Thread: The Toyota

Well I think it's time I start my own build thread. It's a single cab toyota that I bought off dr from Eric, thanks Eric for the sweet truck.
The Build:
Total Chaos
62 inch springs
22r
fox shocks
32 gal fuelsafe
Well most of you know now that Erics truck has gone to a new home. The second day unloaded the truck, started welding the cage, adding plates, made new fuel cell mount, primer & painted cage, made door panels & dash. Heres some pics of the build so far.

Hell yea,keep us posted. always wanted to see this truck get finished

This truck is going to be one of the nicest reg cab leaf sprung Toyotas out there. Jeremey is not fucking around with this thing.

just picked up band new msd 6 series offroad road ignition and does any body no about notching the frame support 4 drive shaft clearance any input would be appreciated

Now I found the thread! Looking good Jeremy, post pics of the motor!

either tonight when wife gets home or tomorrow i hate fucking computers

hey aj got any pics on your dash

No dash for me....just a tube with a steering wheel, a GPS, race radio and intercom mounted to it...lol

Originally Posted by 22r stroker

either tonight when wife gets home or tomorrow i hate fucking computers

if you got pics and want to send them to me ill post them for you... pm if intrested

hey anything about the notching support 4 driveshaft clearances if so post pics cause iwas looking at travisfab truck and its notched

No notching on my truck....where's your clearance issue? The crossmember at the rear of the cab? It should clear by a long shot...

Yeah, he is talking about the crossmember that is underneath the rear of the cab. My truck is notched, and I remember Tortuga being notched as well.

exactley aj what im talking about just havent cycled it with driveshaft in and seen travis just thought i would bring it up . cvc prerunners dont give up on your build shes getting close to being completed keep it going dont sell

Hmmm...didn't have to notch mine, it only has 16" of travel but it compresses all the way...

hey u coming down for the dash or u going to stay up north

Originally Posted by 22r stroker

hey u coming down for the dash or u going to stay up north

Don't know yet...depends on if we go to Washington for Christmas or not...

what are u doing this weekend

well got some bad news today trucks going to take acouple more months then planed do to my wife wanting to finish her masters so prioritys firsth oh well whats a couple more months cvp prerunners i see your pain my freind i am in the same boat parts all over and cant yous them

Originally Posted by 22r stroker

what are u doing this weekend

Prepping for the Glen Helen Race...

Nice Build.... That painted cage looks good.

Praise the Lord this thing is going to see some dezert!!!!! I remember when Eric started it, cant wait to see it finished. Good luck dude!

Rad Jeremy! Glad to see this thing FINALLY get finished! Here's a some pics of what it looked like when it left us!

yeah if everything goes well be out in about 4 to 5 months cant wait still debateing on what seats berad or spacro any input on these would be great thanks

Originally Posted by 22r stroker

yeah if everything goes well be out in about 4 to 5 months cant wait still debateing on what seats berad or spacro any input on these would be great thanks

I say mastercraft or beard. Truck looks sweet

Truck looks good Jeremy! Cant wait to see it running! I second on the Mastercraft or Beards.

whats all the main stuff to finish? but yea i took on to much at one time and greg is saveing me lol


i agree with dunerider,i just bought a pair of mastercraft pro-seats and they are amazeing.

yeah just dont know wich ones so many nisc seats and thanks gimmiesand 4 the ignition thing is fuckin sweet wiring will be gettin done next month cant wit then some other little things to do then run this bitch

not that much once wiring done shocks and couple little things pretty much have every thing else motor tranny springs glass ect.............

I've seen the truck in person, it's a real work of art. Good job Richer Racing. The dash panel is looking good. I can't wait to wire it.

Remember, don't rush it man! It's gonna be a sweet ass truck when finished.

I'm running Mastercrafts and love them! Since we're not running TT or Class 1 speeds we should be fine with suspension seats...

aj what mastercrafts are u ruunin and any body know agood fuel pump[ 4 carbed motors any input would be great

I think they are Mastercraft Pro-4's...they should be the same as the ones pictured above but in grey...

Originally Posted by FCORR

I think they are Mastercraft Pro-4's...they should be the same as the ones pictured above but in grey...

yup,thats what mine are

A few pics from today, more to come...

Originally Posted by travisfab

a few pics from today, more to come...

what hubbs are those? Would they fit on my 4x snouts?

Those are Gold Line hubs for a 2wd Toyota. Not sure if they made them for a
4X4 spindle. But as far as I know, they don't make them anymore.

Originally Posted by GLAMISPERSON2121

what hubbs are those? Would they fit on my 4x snouts?

2wd drive Goldline's, (Baller). Have not ever seem them in a 4x version.

The truck looks good.

Originally Posted by GLAMISPERSON2121

what hubbs are those? Would they fit on my 4x snouts?

JSI makes 4x hubs

Toyota 4x4 billet hubs

More Pics






Motor pics are a little blurry

Bling bling looks tits.